Upper Register Performance Soprano Sax - A Question

A question was posed to me last week and as there are many elements of my reply that might be of interest to others I offer the following on this topic.

Question:

I struggle with getting high notes on my soprano sax. Should I change my reed (strength) ?

Reply:

Changing your reed strength may be helpful but just playing a harder reed (I have to assume this is what you mean) will not necessarily be the answer. The soprano sax should not be more ‘difficult’ than other saxophones but its small size means that it may be more critical. Little things will make big differences. Every aspect of your playing technique is ‘under the microscope’ in ways larger saxes do not require to the same degree. This is why prior experience in alto or tenor sax is usually recommended before adding the soprano to your saxophone armoury.

There are many factors that will affect the response and stability of the saxophone upper register, especially on soprano, so a review of them may be useful:

• The embouchure must still be ‘round and supportive’ but not too tight. Playing a stable concert C on the soprano mouthpiece setup alone is a good target (concert Ab for alto, concert Gb for tenor).
• The correct amount of mouthpiece in the mouth is very important – too much in the mouth and the sound and upper register response will suffer, too little and the tone will be dead and both high and low registers will be compromised.
• The airstream used should feel significantly faster for the soprano and if the high notes are unstable you may need to ‘focus’ the air into a smaller yet still energetic stream in order to provide what the upper range notes require.
• The quantity of air used for different registers will need to be varied – higher, shorter tube notes require less (they are easy to overpower) whereas lower, longer tube notes will require a proportionally greater volume of air to fill the tube and stabilise their response.
• Inside your oral cavity the tongue must have a more exaggerated ‘arch’ position than what you use on the alto, tenor or baritone and this arch is closer to the rear of the mouth. This is a bit like saying the vowel sound ‘Eeeeee’
• Your mouthpiece must be in a good tuning position on the cork. If pulled off too far the low notes will not speak properly and high notes will be very flat in pitch and unresponsive. If the mouthpiece is pushed on too far on you might think all is okay - until you check your tuning – when you are likely to find the high register to be extremely sharp and the instrument very out of tune with itself.
• If your mouthpiece tip opening is moderate or narrow then a medium to medium strong reed (strength 2.5 to 3.5 in most brands) is likely to be required in order to provide stability throughout the instrumental range, right up to high F# or G.
• If your mouthpiece tip opening is on the larger side a somewhat softer reed may provide a better match. Too strong and you will find yourself fighting the low register and having to ‘bite’ too hard to make your basic sound.
• Higher baffle mouthpieces (including many jazz style mouthpieces) will be generally brighter and in fact may facilitate upper register playing but may also demand more relaxation in the embouchure and ‘favouring’ downward for pitch. Moderate or lower baffle mouthpieces are generally more stable for intonation and are likely be more manageable throughout the entire range.

As a guide I would suggest that you are in search of a reed strength that provides enough resistance to meet the demands of your properly focused and well-regulated airstream without excess embouchure pressure required.

Success with higher register notes should follow.

The tips and comments above are the result of many years of providing help and advice, my personal interest and study, and the teaching that I have done during my career. I have many colleagues and teachers to thank for sharing their thoughts and suggestions on this and other topics. In addition I am indebted to Woodwind & Reed, Cambridge ( www.wwr.co.uk ) where, in the course of helping customers, many of these concepts have been refined and have proven helpful. 

Thomas Dryer-Beers

Thoughts on Clarinet Double Lip Embouchure

Reprinted from an article for the Clarinet & Saxophone Soceity Single Reed Doctor

Question:

I have recently overheard friends speaking about using a ‘double lip’ embouchure on the clarinet. What is this and will it help me?

SDR Reply:

The standard clarinet embouchure, used by most players is known as a single lip embouchure, one where tissue of the lower lip tissue is folded over the lower teeth to form a cushion and contact the reed. The upper lip then lies in front of the upper teeth where they contact the mouthpiece and the lip’s role is to wrap around the mouthpiece to keep air from escaping.

The double lip embouchure, as it sounds, uses both lips to wrap over the teeth therefore placing lip tissue entirely around the mouthpiece – no contact from the teeth on the mouthpiece at all.

For some players with either very thin or rather large lips, a double lip approach is simply not a physically practical option. For others it could be considered an option but it does take time and much practice to learn and to grow comfortable with the position of the upper lip between teeth and mouthpiece.

A double lip embouchure places a great responsibility on the power of an air stream to generate sufficient pressure to vibrate the reed – without the benefit of the regular ‘grip’ between upper and lower teeth. Any attempt to ‘squeeze’ the reed shut with jaw pressure is likely to result in pain as the lips, especially the upper lip, will be trapped by the teeth.

The potential benefits of a double lip approach are:

·        A rounder, warmer sound may be developed as all tendencies to compress reed and mouthpiece are unlearned

·        The necessity for much greater awareness of air stream support leading to better control

·        An increased awareness of all elements of tone production

·        Greater subtlety in control as lips are simply more sensitive than teeth

·        A strengthening of upper lip muscles as they are engaged in a new ‘drawn down and in’ position

·        A genuine rethink of what it means to ‘properly blow’ your instrument

Possible downsides include:

• Pain and the risk of damage to upper lip tissue whilst learning the embouchure position
• Fatigue of the facial muscles while adapting to a new approach
• Loss of upper note accuracy and response due to the loss of familiar pressure from the lower lip
• A potential need to move to softer strength reeds
• A feeling is instability in holding the instrument still while playing

You can see from the above that there can be numerous benefits, principally in the area of tone production and flexibility but there are many possible risks to consider and for many the double lip approach is not a viable option. (NB - I would never recommend it for use on the saxophone due to the different holding angle of all saxes, even including soprano.)

My own opinion is that giving double lip approach a try, if for nothing else as a spur to develop a better awareness of REALLY GOOD AIR SUPPORT, is worth the time invested experimenting for all those who can manage the drawn down position of the lip.

After a period of time spent experimenting and benefiting from the improved breathing and blowing skills acquired I would recommend, for the vast majority of players, a return to a single lip embouchure combined with the use of a mouthpiece cushion and the application of all the positive elements experienced:

• Better initial breathing awareness
• MUCH greater support from abdominal muscles while blowing
• A more relaxed ‘grip’ from the jaw muscles
• Increased involvement from the upper lip in the surrounding and support of the embouchure on the top of the mouthpiece

All the above can only improve a players normal sound and ability to control their instrument so what is there to lose?

--------------

The tips and comments above are the result of many years of providing help and advice, my personal interest and study, and the teaching that I have done during my career. I have many colleagues and teachers to thank for sharing their thoughts and suggestions on this and other topics. In addition I am indebted to Woodwind & Reed, Cambridge ( www.wwr.co.uk ) where, in the course of helping customers, many of these concepts have been refined and have proven helpful. 

Thomas Dryer-Beers

Who Might Succeed on the Bassoon?

Who Might Succeed on the Bassoon?

While it is possible to begin upon many types of instruments when a child is younger and smaller the bassoon is not usually consider to be one of them. Until the advent of 'mini bassoons' pitched in G even the innovative 'Short Reach' models which helped make key work manageable for smaller sized hands by reducing the 'finger stretch' required were based upon full size, standard weight instruments. Thus, by default, most players coming to the bassoon have traditionally done so from other woodwind instruments or none, rather than having done their early musical training on the bassoon.

This brings up a relevant question - Who, or rather, what instrumental background, is most likely to be conducive to success on transferring to or adding the bassoon to their instrumental portfolio?

The Recorder can be an excellent preparation for the bassoon as its origin in the pre-Baroque period, its repertoire and the experience of open holes and crucially its basic fingering patterns have many elements in common with the bassoon. Even not withstanding the absence of experience of blowing a double reed, though this must of course be learned, picking up the bassoon may be less of a challenge than moving say from a single reed instrument, where a very different relationship of embouchures is a distinct difference. The bassoon also offers a recorder player an avenue into more modern ensembles.

The Flute may also be a fine preparation for the bassoon as the nimble finger technique and the wide range of the flute with its own tricky cross fingerings for higher register notes is not dissimilar to the challenges a player will face with the bassoon. Again, the lack of experience blowing a reed may actually be a benefit as the unlearning of an embouchure and the muscle shapes based upon mouthpieces can take time. The suppleness of flute embouchure and the natural aural cavity shape and focus of air are likely to make the learning of the bassoon both a bit quicker and more 'natural'. There will almost certainly be some disruption to ones optimal embouchure on the flute but this may be a small price to pay for the reward of playing an 'endangered species' instrument instead of trying to distinguish oneself amongst a crowd of other flautists.

The Clarinet is often considered as a good training instrument for the bassoon as it utilises a similar pattern of fingerings for much of its lower range and a clarinettist is already used to reading both below and above the stave. It also shares the open holes and thumb register key operation (albeit in reverse!) but a word of caution - the optimal aural cavity shape required for the clarinet as well as the fixed, taught muscle formation of the embouchure are very different than the ideal shape and embouchure for the bassoon. Coming to grips with this very fundamental difference is crucial, and usually requires much patience and careful guidance from a knowledgeable and sympathetic teacher. Failure to understand the differences between the instruments often makes for poor results and a genuine loss of good clarinet habits as well. Experience of playing the bass clarinet can be quite helpful as this larger instrument, with its more flexible embouchure and altered aural cavity, is at least a step closer to the bassoon and the 'role' of the instrument in the band or orchestra is also more similar to the bassoon than that of the Bb clarinet.

The Saxophone can also be a possible successful precursor to the bassoon as the more relaxed embouchure and aural cavity shape used on the sax, especially the tenor and baritone sax, bears a close resemblance to that used on the bassoon. The finger system, though simpler by comparison on the sax than the bassoon, does have a logic that transfers reasonably to the bassoon and, not unlike the potential experience of the recorder player, provides one with an introduction to a repertoire and to ensembles that the saxophone alone only rarely is allowed to entry.

Perhaps contrary to expectations the Oboe is possibly the least logical of the woodwind family to lead onto or share time with the bassoon. This is principally due to the very different experiences of blowing these two double reed instruments. The oboe is highly reliant on a high-pressure reservoir of air emitted in small quantities through the narrow aperture of its reed. The bassoon, while also requiring good air support, uses a larger volume of air more quickly. The relative tension of the oboe embouchure differs greatly compared with the more relaxed bassoon embouchure and the dramatically different amount of reed used beyond the lip in proper blowing position are significant differences that few players mange to accommodate successfully - certainly not without a great deal of practice!

A Pianist or String instrument player may have a decent chance of successfully learning the bassoon as their original instrument is so demanding of finger dexterity and reading (in the case of the piano) or discipline, precision finger action and tuning (in the case of string instruments) that the demands of the bassoon may not seem a great challenge - and they have a advantage of not having to unlearn anything in the way of embouchure! Such players can concentrate upon getting things right the first time.

Finally, if a Brass player, especially a low brass (trombone, euphonium or tuba) player is interested in playing the bassoon and is willing to learn take of the challenge of the fingering system, the foreign blowing feel with the reed inside the mouth (instead of the lips vibrating) and the very different sound production of relying upon a double reed, there is little danger of them doing harm to the playing of their original instrument. They will likely already have experience of reading the bass clef and the embouchure of the lower brass instruments is much less likely to be disturbed by the bassoon. Players of the more defined embouchure higher brass (trumpet/cornet, french horn, tenor and baritone horn) are only very rarely likely candidates for playing any woodwind instrument, including bassoon.

-------------------

The tips and comments above are the result of many years of providing help and advice, my personal interest and study, and the teaching that I have done during my career. I have many colleagues and teachers to thank for sharing their thoughts and suggestions on this and other topics. In addition I am indebted to Woodwind & Reed, Cambridge ( www.wwr.co.uk ) where, in the course of helping customers, many of these concepts have been refined and have proven helpful.

Thomas Dryer-Beers

Placement of Single Reeds on Mouthpieces and a Useful Test

Placement of Single Reeds on Mouthpieces and a Useful Test

Over many years customer have regularly asked me how best to place their reeds on their mouthpiece. Since the reed and mouthpiece combine to vibrate the air column this actually quite an important question. 

Following soaking, the reed should be positioned on the mouthpiece with the reed lined up evenly distributed on the flat cutaway that is the mouthpiece ‘table’ with the tip of the reed aligned with the end of the tip rail of the mouthpiece. When examined perpendicularly you should be able to see a hairline of the tip rail over top of the reed tip in standard playing position. Once you are satisfied with the positioning hold the reed with a thumb and carefully place the ligature over top. Lower the ligature until it sits in a position where there is an equal amount of the ‘bark’ of the reed visible on either side of the ligature. Tighten the screw(s) (where present) finger tight but do not over tighten them as this can damage the reed fibres and inhibit vibration.

If you wish to check the success of your placement you can perform a suction test as follows to see if the reed is ready to use:

• Wet the palm of your hand and place the shank end of mouthpiece end on your palm

• Take the tip of the mouthpiece and reed in your mouth, wrap your lips around the mouthpiece and create a vacuum by sucking aggressively and repeatedly to remove air from within the mouthpiece

• When you feel this has been achieved release your lips and the reed should hold shut for a few seconds (you may even hear a ‘hissing’ sound) before it ‘pops’ open with a noise, as the vacuum is lost.

• If you do not get a ‘pop’ first try again – If after repeated attempts your reed does not hold a vacuum it may be miss-aligned, warped or damaged. If it seems to take a very long time to ‘pop’ then if may be fatigued and ready to be changed.

It takes a bit of practice to gain ‘the knack’ of this test but it can be quite useful in confirming that the set-up is likely to work well.

----------------

The tips and comments above are the result of many years of providing help and advice, my personal interest and study, and the teaching that I have done during my career. I have many colleagues and teachers to thank for sharing their thoughts and suggestions on this and other topics. In addition I am indebted to Woodwind & Reed, Cambridge ( www.wwr.co.uk ) where, in the course of helping customers, many of these concepts have been refined and have proven helpful.

Thomas Dryer-Beers

Why Play the Cor Anglais?

Why Play the Cor Anglais?

I imagine that almost any oboist who has had experience playing or owning a cor anglais will be inclined to answer quickly simply and immediately - because it is fun! I fully share and support this opinion - but it does not say enough about the benefits to the oboist so I hope to expand a little. I would say that experience of playing and better yet owning, playing and treasuring your own cor anglais deserves to be viewed as an important part of the development and maturation of every oboist.

The similarities between oboe and cor are many and following a predictable initial shock and the requisite alteration of habits and expectations transferred from the oboe the cor is largely playable by most oboists of a reasonable standard. The primary differences one will at first encounter are the relatively larger size and weight of the instrument, the stretch fingers and placement of keywork and the blowing position as the cor does rely upon a bent crook.

The size and weight are best addressed by using a sling, a fairly standard practice for the cor, to take the weight and relax the hands. The finger stretch and placement do take some getting used to however, since the demands for speed of finger action are considerably lower for most of the cor repertoire, there is usually time and opportunity to learn to ease the fingers into place to cover holes correctly and gently.  Allow the instrument to hang down between the legs so that the reed on the crook enters your mouth at approximately the same angle as you have with your oboe reed. Transferring some of these skills back to the oboe is often beneficial in itself and may eventually result in a more fluid technique on your main instrument.

Oboists often discover that the cor uses up a greater amount of air than the oboe. This is true and logical if you consider the larger size bore. Learning how to breathe more deeply and how to best hold onto the greater reservoir of air required is a very useful learning process and the discipline and awareness that one learns are sure to enhance breathing and phrasing on the oboe as well.

The Cor Anglias is almost entirely a solo voice in the orchestra or ensemble and as such when it is included in a score it is intended to be heard - almost never a 'filler'. This implies that tone and projection are very important concerns for the player. Mastering the production of a fine, centred, colourful tone with good projection takes time and more than anything replies upon learing to relax the embouchure so as to not 'stifle' the sound with the same embouchure pressure as one uses on the oboe. In addition the aural cavity should be adjusted to 'shape' the air to optimise the resulting tone colour by giving 'space' for the air within the body before filling the reed/crook/instrument. Getting used to hearing oneself instead of feeling 'buried' within an ensemble texture can be a bit nerve wracking to be sure but it also can be a wonderful confidence boost!

Balancing the tonal qualities of different ranges of the cor requires careful listening and the cultivation of new sensitivities. The skills gained through this process are likely to benefit the oboe as well. Learning to produce and then employ vibrato is ofter easier to do at first on the Cor Anglais as it is a more flexible instrument and a wider amplitude of vibrato and a slower speed can be acceptable. Vibrato skills learned on the cor can later be transferred to the more precise demands of the oboe.

Even if one does not make their own cor reeds learing how to handle and adjust a different size of reed can be very useful. Most players will play a less resistant reed on their cor than their oboe and learing to 'take pressure off the lips and place emphasis upon the air' will not only make for a better cor sound and more accurate intonation but can be applied to the oboe often with great benefit.

Learning to switch between, care for and maintain your instrument is also very beneficial as it is often the case (even likely) that your oboe and cor will have been made by different manufacturers and the key mechanisms and even the specification (covered hole, ring system, thoumbplate, conservatoire system, half hole split keys, LH F, trill keys, 3rd octave key, etc.) will be different. Coping with this is a fact of life for many players and it should make you a more flexible individual capable of understanding all your equipment better.

I would recommend splitting your practice time between the different instruments on a regular basis. Playing scales, arpeggios, interval studies and long tones on the cor is time well spent. When the much smaller, lighter and more facile oboe is picked up it is almost certain to feel amazing by contrast.

A final point I would add is that the ability to play the cor, and the ownership of or access to an instrument, can often be the 'ticket' to opportunities to perform with a wider range of ensembles and even result in participation in groups where just being to provide the oboe would not be of interest.

I would encourage all oboists to embrace whatever opportunities they get to play the Cor Anglais. Make sure any instrument you might use is in good condition by having it checked over by a repairer and then go away and do the necessary 'familiarisation' practice. When you feel that you are ready then go out and let everyone know that you have added cor to your skill set. You will be glad you did!

--------------

The tips and comments above are the result of many years of providing help and advice, my personal interest and study, and the teaching that I have done during my career. I have many colleagues and teachers to thank for sharing their thoughts and suggestions on this and other topics. In addition I am indebted to Woodwind & Reed, Cambridge ( www.wwr.co.uk ) where, in the course of helping customers, many of these concepts have been refined and have proven helpful.

Thomas Dryer-Beers

The Importance of the Air Stream in Wind Playing

The Importance of the Air Stream in Wind Playing

In my teaching and throughout my time advising in the retail shop environment the topic of good air support has always been very important. I certainly did not know enough nor pay enough attention to developing good breathing and support habits when I was younger and many other players share the same difficulties and frustrations that I had. Indeed it was only in my early twenties following a great deal of rethinking and the guidance of some significant teachers that I began to sort myself out. Now many years later I believe that I am ready to refine what I have experienced and found useful to hopefully help others.

Breathing...Where it all begins.

Wind instrument playing all begins with a relaxed. efficient intake of air. Taken properly, utilising the greatest lung capacity available and dispensed under controlled pressure appropriate to the requirement of the instrument involved, an air stream is created that will energise an air column, then a reed or set of lips to do exactly what is desired for the musical execution of a phrase. Anything less that total control and execution will result in some level of musical loss - the air stream is that important.

When taking a breath the first stage is getting enough air into the lung quickly. Most tutors will advise opening the mouth, clearing the past of access to the throat, pushing out the abdominal muscles energetically and allowing air to 'rush in' to fill the void. Try standing or sitting in a well balanced position and work to expand your abdominal cavity in all directions: downwards, outwards, up to the bottom of the rib cage and at the back. I say to pupils that this is like trying to make oneself intentionally 'fat' with air.

If taken in successfully this large quantity of air will be held under pressure via the expanded 'stretched' position of the intercostal abdominal muscles for a brief period of time as you begin to release the air by blowing out. The challenge comes as the volume of air is reduced as you play. One must attempt to keep the air pressure constant while this loss of air is taking place by continuing to think of pushing the abdominal muscles 'out' - in other words keeping them engaged in the process of air support and not allowing them to merely collapse as the volume of air decreases. This is perhaps counter-intuitive but the action of attempting to 'compress' the abdominal muscles will only add tension to the process of blowing. Try taking a breath, beginning to speak and then, while speaking squeeze the abdominal muscles inwards. Your voice is likely to break or sound 'strangled' by this squeezing. Imagine what such undesirable tension could do to your instrumental tone!

Tongue and Oral Cavity Shape - Whistling

The shape that the player imparts to an air stream is another very important and altogether under appreciated aspect of tonal control. Many teachers speak of 'singing' via the instrument or illustrating good practice by using a series of vocalisations of various vowel sounds, i.e. Ahh, Eee,  Ooo, Ohhh. While this approach does work for some players I believe that it is not the most direct means of imparting an understanding of best practice positioning of the tongue. In my teaching I have found it more useful to suggest that a pupil first whistle for me - and notice the elevated position of the back of the tongue at the back of the top teeth and the position of the tip of the tongue near and behind the lower jaw front teeth. With the tongue in this position, blowing the air 'faster than you can sustain the whistle sound' is better illustration of an air stream shape suitable for most wind instrument blowing and well as providing a sense of the compression that must take place within the oral cavity. If a player is not familiar with or unable to whistle through the lips all is not lost. I like the following alternate approach: Imagine attempting to drink a very thick milkshake through a very weak straw. The aggressive 'sucking' position and sensitive 'drawn in' shape of the lips closely mirror a whistle position. Reverse the air flow to blowing instead of sucking and you are there!

When playing highly pitched instruments (i.e. Eb clarinet,  soprano sax, oboe, piccolo trumpet, etc.) or the higher regions of any instrument, the elevated part of tongue is best to be shaped high at the back of the oral cavity. As one performs on mid-pitch instruments or low-pitch instruments and lower ranges or pitch the 'focus' point of the tongue arch moves further forward in the oral cavity. Experimentation with this positioning can greatly aid the understanding involved in successfully 'doubling' between different size instruments i.e. oboe to cor anglais, flute to alto flute, Bb clarinet to bass clarinet, etc. and between different families, i.e. clarinet to saxophone, flute to bassoon, trumpet to trombone, etc.

'The Two Q's': Air Quantity and Quality

I firmly believe that the notion of how to deal with the variable column length and dimension of tubing that is fundamental to all wind instrument playing is vital and under appreciated. The concept of 'The Two Q's' is something that I have synthesised from many methods of trying to explain this elusive concept. The sensitivity of a player to the requirements of his or her instrument is vital to the development of instrumental control and this succinct summary will hopefully be both helpful and memorable:

• Players should always take care to supply the appropriate Quantity of air for whatever notes are being played, varying with the register, the volume being attempted, the length of the sounding tube, the type of attack being used and the timbre or expression sought.

• They must continually support and always use the best Quality of air that they can produce - this never varies and is the foundation of all beautiful playing. The degree of success one has in musical performance at all stages of learning is usually a direct indication of how well this principle has been understood and incorporated

 

 A Method of Practice

 

When faced with a phrase or section that contains many and various challenges to achieve the best possible musical expression many players resort to the repetitive practice of small sections, connecting up notes, addressing finger changes, experimenting with various dynamics, etc. This traditional approach is perfectly valid and often absolutely necessary. In addition I would like to propose a further practice option that in my experience is often overlooked. That is to play all or part of the phase(s) in question utilising at first a single pitch. This can be chosen from the phrase or completely unrelated. Within this sustained note one should try to express all the dynamic shape, control and duration of the original phrase. Once satisfied one can try introducing a selected series of note changes which begin to represent the phrase shape and challenges, perhaps the first notes of groupings or the extremes of interval leaps of the most dramatic of the required volume differentials - without sacrificing the overall control gained on the one sustained pitch. Once these intermediate stages have been successfully managed then work to add in further notes and/or finger changes until the entire phrase is being performed as intended.

If for instance an entire 4 bar phrase in a given tempo can be played with one breath using a sustained single pitch then the same 4 bar phrase should be able to be successfully played in the same tempo no matter how many subdivisions of notes are present or how wicked the intervals. If one struggles it is likely to be due to undesirable tension, less than ideal breath control or a lack of concentration while one is preoccupied with notes. Take a step back, practise the simplified phrase till confidence grows and then try again.

Very best wishes.

-----------------

The tips and comments above are the result of many years of providing help and advice, my personal interest and study, and the teaching that I have done during my career. I have many colleagues and teachers to thank for sharing their thoughts and suggestions on this and other topics. In addition I am indebted to Woodwind & Reed, Cambridge ( www.wwr.co.uk ) where, in the course of helping customers, many of these concepts have been refined and have proven helpful.


Thomas Dryer-Beers

The Clarinet Intonation Learning Curve

The Clarinet Intonation Learning Curve


Perhaps you remember your first sounds on the clarinet? Mine remain fresh in my mind even after many years. They were frankly ugly, unpredictable and unrewarding - but I was determined to get better and of course, with practice, things did improve. Almost everyone who begins playing the clarinet will have some version of my experience and perhaps by sharing some of the usual stages of progression to playing well some benefit can be gained and some frustrations avoided.

Pre-Grade 1 to approximately Grade 2 standard -

When we begin the initial sounds, when they are produced at all, are often very spread in tone and flat in pitch. A combination of a yet to develop embouchure, often too great a quantity of air in use and a thin reed make such results predictable. Manufactures know this is likely to be the case and they design their student instruments to be able to correct for this when assembled completely 'pushed in'.

A helpful tip is to not worry too much (or not at all) about the higher (clarion) register and to concentrate upon making a good and predictable tone in the lower (chalumeau) register. As most beginners seem to be recommended to begin on a soft reed, strength 1.5 usually, this should work well for starting off but by the time one comes to play in the upper register it is probably best to have moved on to a slightly stronger strength. Strength 2 or 2.5 depending upon the brand would be my recommendation.

Whilst still concentrating on the low register it is possible to improve the tone quality by concentrating on using a well-supported, fast moving air stream that is delivered to the instrument in an appropriate quantity for the note(s) being played. It is worth checking that a Concert C can be sounded on the clarinet mouthpiece alone. This is the highest pitch sensibly available on the mouthpiece and the only correct pitch when the embouchure and air are in balance.

A useful concept that I have often shared is:

'The Two Q's': Quantity and Quality.

Players should always be aware of supplying the appropriate Quantity of air for whatever notes are being played, varying with the register, the volume being attempted, the type of attack and the timbre or expression sought.

They must always use the best Quality of air that they can produce - this never varies and is the foundation of all beautiful playing. The degree of success one has in musical performance at all stages of learning is usually a direct indication of how well this principle has been understood and incorporated.

Grade 3 to approximately Grade 6 standard -

So, after beginning to play and everything seem to be pitched flat one is improving, blowing better air, managing with a firmer reed and the embouchure is beginning to develop. The upper register is being attempted and expectations are rising. So often is pitch! It is time to consider pulling out the barrel from the top joint of the student clarinet (up to 3mm is not unusual) and even consider additional 'distributive tuning' at the middle tenon and at the bell if necessary. Often a willingness to play with too great an embouchure pressure has taken over the best practice on the supply of air. If this is the case a symptom may be that newly learned altissimo register notes (D3 above the staff and higher) will likely be thin sounding, unstable and 'brittle' as well as sharp. Keep working at The Two Q's and remember - high notes are not meant to be hard to play - they are just more demanding of accuracy in blowing.

Grade 7 and beyond -

You will hopefully have upgraded to a higher quality instrument and better mouthpiece by now. In addition your altissimo notes (high F, F#, G and above) have become an important focus and regular expectation for your playing, hopefully your overall tuning has begun to stabilise and the characteristics of your instrument, as designed by the manufacturer are beginning to be recognised. You should be aware that your lowest 'bell notes' (low E through low F#) are usually low in pitch so that the corresponding 12th above (middle B, through C#) are not uncomfortably sharp in their tuning. Left hand first first finger and thumb E and thumb F are often intentionally a bit low so that their overblown 12ths, the upper B and C, are not incorrect-ably sharp. Throat A and Bb, notes that once seemed very flat and ugly in tone now are much closer to true pitch and will actually benefit from the addition of combinations of right and left hand fingers, referred to as 'resonance fingerings' that will help to lower pitch and enrich the tone.

It is worth reminding oneself that the clarinet, as with all wind instruments, is an acoustical compromise with inherent challenges to be overcome. Once these known compromises are recognised and understood it is possible, with a well supported and appropriately shaped air stream and flexible embouchure control, to obtain predictable and very functional intonation - ultimately leaving one able to match and blend with other players, difficult performance conditions and ensembles where other players do not play as well 'in tune' as you do!

------------------

The tips and comments above are the result of many years of providing help and advice, my personal interest and study, and the teaching that I have done during my career. I have many colleagues and teachers to thank for sharing their thoughts and suggestions on this and other topics. In addition I am indebted to Woodwind & Reed, Cambridge ( www.wwr.co.uk ) where, in the course of helping customers, many of these concepts have been refined and have proven helpful. 

Thomas Dryer-Beers

Reed Squeaks - Why this happens and what to do when it does

Reed Squeaks - Why this happens and what to do when it does

Almost all clarinet and saxophone players have at some point experienced their reed 'squeaking', often it seems in a most embarrassing situation or circumstance. Other reed players will usually offer sympathy - players of different instruments (brass, strings, percussion) just wonder what is going on - as we might well also. Here is my attempt to explain the 'reed squeak' in layman's terms and a few suggestions for what once can do to help.

The squeak of the reed is an uncontrolled harmonic or unintended sounding due to the vibration of the air column being adversely or improperly generated, usually at the mouthpiece / reed end or sometimes within the tube of the instrument.

Checklist:

• If this should happen to you the first place to check is the reed 'seat' on the mouthpiece. One can check this visually using a straight edge ruler or knife, sighting along the flat underside of the reed and looking in the direction of a strong light source. If light 'leaks' or shines through a gap under or around the reed then the cane has warped and must be flattened either by careful scraping using the straight knife blade or rubbing the reed on a sandpaper placed on a flat surface. A reed resurfacer may also be used for this purpose. Once the cane underside appears flat again retest by playing and see if the problem has disappeared. A suction test can be performed to see if the reed will do its job properly again - here is how:

Place the reed on the mouthpiece and tighten the ligature as normal. Lick or wet the palm of the hand. Place the 'back end' of the mouthpiece on your hand and placing your lips around the tip of the mouthpiece aggressively suck backwards removing as much air from inside the mouthpiece as you can. Release the mouthpiece from your lips pulling it out and hopefully the reed will hold in the closed position for 2-3 or more seconds until the vacuum is lost and the reed 'pops' open with a noise. This test takes a bit of practice but once you get the knack it is a very useful indication of a reeds state of readiness to perform.

• Less frequently wear or damage can occur to the facing of the mouthpiece itself and this can be the source of a air leak either between the reed and the 'table' of the facing or on the rails or tip where they come into contact with reed. This type of wear is often difficult to detect but if problems with squeaking or reed response are a regular occurrence then this may well be the explanation. Try some different mouthpieces and / or visit a mouthpiece craftsman with the proper tools to check and measure the mouthpiece.

• It is also possible on both clarinet and saxophone that a hairline or larger leak is affecting the accurate sounding of one or more notes. This can be due to pad seating but is often more subtle sometimes on the clarinet occurring due to an incomplete closure of the finger to the top of a tone hole on the instrument - i.e. the ring positioned to 'high' or the incomplete closure of a pad due to a ring positioned too 'low'. Check especially the left hand 1st and 2nd finger rings and the right hand rings. If your finger(s) bottom out on the tone hole before the ring fully closes the pad a leak will be present. If the pad closes before the ring allows your finger to cover an open hole air can leak out under the finger. Bend the key work in the appropriate direction to overcome the non-alignment. A butter knife or other thin, flat metal plate can be used.

• Common sources of response problems for the saxophone is found in the correspondence connections relating to the left had 2nd finger touch (which must hold down 3 key/pads in total) and also the right hand correspondences to the F# pad. Regulation screws, where present may help to return the correct function of these keys but be prepared to insert a butter knife or other thin, flat metal plate underneath a pad to be able to close a related key arm to overcome the closure problem. If you go too far you may have to reverse the process.

• Poor regulation of the G# key screw can account for poor performance of low C#, B and Bb. I recommend that this be checked each time you play.

• Whenever key work is adjusted there is a chance that the attempted correction will not go well or even be the wrong answer to a problem so having a good repairer available to visit should your best emergency efforts fail is always advisable.

-----------------

The tips and comments above are the result of many years of providing help and advice, my personal interest and study, and the teaching that I have done during my career. I have many colleagues and teachers to thank for sharing their thoughts and suggestions on this and other topics. In addition I am indebted to Woodwind & Reed, Cambridge ( www.wwr.co.uk ) where, in the course of helping customers, many of these concepts have been refined and have proven helpful.
 

Thomas Dryer-Beers

The Saxophone Intonation Learning Curve

The Saxophone Intonation Learning Curve

When a player begins playing the saxophone it is natural to accept just about any sound and tuning as acceptable. After all there are some many other things to think about and the instrument is designed to blow easily and usually does - as long as we provide it with a reasonable air stream and allow the reed to vibrate.

As one slowly gets better and wishes to demonstrate more control over the tone quality a progression towards the use of stronger reeds begins and this is to be welcomed. As the embouchure and the ability to support the air column both develop there is frequently a perception that, in order to keep a reed from 'closing up', a still stiffer reed and possibly a more open tip mouthpiece must be used. While this might be true in some cases is is certainly questionable for many players.

Why is this important? Because the degree of effort required to produce the basic sound and the related embouchure strength used contribute very directly to the ability to play the saxophone in tune.

When beginning the middle range notes we first encounter are fairly predictable and our standards are lower. We do not know how to play 'up high' and are not often asked to do more than honk out low notes. The overall tuning is often rather flat and the tone unfocused. As progress is made and high notes are attempted they are usually found to be thin in tone and can be unreliable. It follows then that we are suggested to try a stronger reed to aid playing in this upper register. In the normal course of events this change makes the high palm key notes easier to produce and makes the playing of lower notes more challenging. With a bit more practice and progress a sensitivity to a more consistent tone and pitch begins to develop and, following tuning to a concert A (or Bb) as one will usually start out doing, comes the realisation that even in this 'in tune' position upper octave notes will often be quite sharp, lower register notes (low D and below) quite flat, middle D very sharp and, especially when played in close proximity to the middle D, the middle C# will be found to be very flat.

This realisation can be and often is very upsetting to the player and can be the beginning of a great deal of searching for answers to the problem of 'playing out of tune' including changes of equipment and much self doubt. What is missing is a simple realisation that all players and especially teachers should try to keep in mind at all times:

The design of all acoustic wind instruments is a compromise and best performance relies upon the player understanding the compromises made.

 

An octave key is only an aid, it is not a substitute for correct blowing and proper 'voicing' in the aural cavity for the register desired. An embouchure that is ill formed (too tight or too lose) can distort the tuning of any instrument. A poorly supported air column will cause response and tonal problems even with the finest of equipment available. An internal shape in the aural cavity will compromise the response and tuning despite the very best embouchure.

The best tuning position for the mouthpiece on the crook is where (with whatever skills the player has by that stage developed) the greatest portion of the instrument's range can be manipulated into an acceptable 'pattern' of tuning.

 

 Manufacturers try to anticipate what their customers will be able to manage and are of course taking advice on their designs from highly experienced performers. Each firm then decides how to accomplish the goal of creating instruments of character with stable intonation patterns.

The saxophone, with its two and one half octave standard range, relies upon two octave vents that are automatically linked to switch depending upon the fingering used (the exchange happens between upper G# and A). The first note that benefits from an octave key will always have a tendency to be sharp - on saxophones this is middle D and upper A.

NB - If for the player these two notes (middle D and upper A) are not able to be adjusted down ('lipped down') to pitch successfully then this is an indication of a deeper problem with air support and embouchure that must be rectified - this will benefit all notes on the sax. I suggest checking the pitch sounded playing on the mouthpiece alone. This should be no higher than a concert A, better an Ab, for the alto, for tenor concert G, better a Gb, for the soprano concert C and for baritone concert D.

The last notes prior to the engagement of an octave key will be weaker and have a tendency to be flat - on saxophones this is middle C# and upper G#. The upper G# in particular (and sometimes G) will often 'fall' or break downwards in the absence of a well supported air stream. The response and accuracy of all other notes within the range of the interval of the vent's use will vary proportionally with their position within the range of the vent. There will always be a 'stretch' between the octaves of the same fingered pitch.

The longest 'bell' notes will often be flatter not only because the instrument often does not 'warm-up' sufficiently for this end of the sax but they must not be tuned 'sharp' or the overall overtone characteristics of the instrument will be affected. High register palm key notes will often be sharp not only because they are at the mercy of a correct embouchure and air balance but also because that end of the instrument becomes very warm through constant playing and the last thing a player wishes to find is that they should have to 'lip up' a high note when so much effort is being made to achieve the best tone and tuning through relaxing the embouchure throughout the rest of the range.

Understanding and accepting that such compromises in designs are inescapable will hopefully prompt attention being given to achieving the best possible air/embouchure/aural cavity position while playing and lead on to anticipating the now much smaller corrections required to address the remaining subtleties of correct pitching.

---------------


The tips and comments above are the result of many years of providing help and advice, my personal interest and study, and the teaching that I have done during my career. I have many colleagues and teachers to thank for sharing their thoughts and suggestions on this and other topics. In addition I am indebted to Woodwind & Reed, Cambridge ( www.wwr.co.uk ) where, in the course of helping customers, many of these concepts have been refined and have proven helpful.
 

Thomas Dryer-Beers

The Flute Learning Curve

The Flute Learning Curve

 When one begins to learn flute there is a lot to think about: developing a correct embouchure shape, the blowing angle, proper breathing, finger placement, standing position - even just holding the instrument properly. Simply managing the making of tone of any kind is an achievement! Almost always the first sounds are often very breathy, weak and inconsistent. Very frustrating for all. 

However, if one is patient control begins to develop with practice and repetition and eventually the beginner becomes functional over a range of the first and perhaps second octave of the instrument. This is enough for most players to join a group, play some solos and generally feel good about their music making. 

At some point comes the realisation that not every note is sounding as good as the others and some notes may seem more difficult to play and possibly even be out of tune with other instruments in the group or band. At this juncture the guidance of an experienced teacher, if this has not already been available, becomes a necessity - for learning how to focus and shape each individual tone to sound its best and to take its place in a reliable, predictable intonation pattern is vital. This is a goal of every player and careful attention needs to be paid to fundamentals to achieve this.

Here is a short checklist:

• Is my stance correct, i.e. balanced weight, feet spread apart, able to move without tension?
• Am I breathing fully and supporting the breath well once taken?
• How are my lips 'addressing' the embouchure hole? Are they relaxed and supple?
• How and where am I directing my air stream?
• How efficient am I being when moving across larger leaps or octaves?
• Are my lips under control - moving easily and only as required?
• Is the tone quality the same throughout all registers?
• Can I play upper notes quietly and lower register notes loudly?
• Do all notes respond to slurring as well as tonguing?
• Can I play softly and stay in tune (avoiding the pitch dropping)?
• Can I play loudly and not go sharp?
• Am I tonguing efficiently or is my tongue stroke disrupting my lips?

Also check:

• Is my headjoint cork in the correct position? (Insert the bottom of the cleaning rod and check the line is in the centre of the embouchure hole)
• Have I pulled out the headjoint an 'appropriate' amount? (For most players approx 6-8mm to A440 pitch position)

All the above points deserve consideration and the time spent improving and developing control will be very valuable. As a general observation improving or intermediate players often play sharp without being aware of it and, until remedies are pointed out to them, they will not know how to respond. Just pulling out the headjoint is not enough as every note has its own 'best' embouchure and blowing angle.

Practice with a tuner will help (and probably shock initially) but eventually the intonation pattern of the instrument begins to be revealed. When this is observed then attention can be given to making the appropriate corrections required while playing to achieve proper tuning. This process can be helped enormously by remembering that very few good sounding, centered and attractive tones will be far if at all 'out of tune' whereas almost all bad sounding notes will be! This leads to a very memorable sentence:

Good in-tone-ation leads to good in-tune-ation.

 

As a quick aid this catchy concept is hard to beat and it can lead on to a lifetime of rewarding and efficient practice. As one reaches top levels of achievement standards the challenges do not end they just change and a player will become able to handle more difficult passages with ease but when faced with something daunting must still go back to basics to figure out how to tackle the problem and somehow make the seemingly impossible appear not only possible but beautiful!

 

 The tips and comments above are the result of many years of providing help and advice, my personal interest and study, and the teaching that I have done during my career. I have many colleagues and teachers to thank for sharing their thoughts and suggestions on this and other topics. In addition I am indebted to Woodwind & Reed, Cambridge ( www.wwr.co.uk ) where, in the course of helping customers, many of these concepts have been refined and have proven helpful.

Thomas Dryer-Beers